<%NUMBERING1%>.<%NUMBERING2%>.<%NUMBERING3%> PRTG Manual: WMI HDD Health Sensor

Sensor Name

Enter a name to identify the sensor. By default, PRTG shows this name in the device tree, as well as in alarms, logs, notifications, reports, maps, libraries, and tickets.

If the name contains angle brackets (<>), PRTG replaces them with braces ({}) for security reasons. For more information, see the Knowledge Base: What security features does PRTG include?

Parent Tags

The tags that the sensor inherits from its parent device, parent group, and parent probe.

This setting is for your information only. You cannot change it.

Tags

Enter one or more tags. Confirm each tag with the Spacebar key, a comma, or the Enter key. You can use tags to group objects and use tag-filtered views later on. Tags are not case-sensitive. Tags are automatically inherited.

It is not possible to enter tags with a leading plus (+) or minus (-) sign, nor tags with parentheses (()) or angle brackets (<>).

For performance reasons, it can take some minutes until you can filter for new tags that you added.

The sensor has the following default tags that are automatically predefined in the sensor's settings when you add the sensor:

• smartsensor

Priority

Select a priority for the sensor. This setting determines the position of the sensor in lists. The highest priority is at the top of a list. Choose from the lowest priority () to the highest priority ().

Serial Number

The serial number of the disk that this sensor monitors.

Size (GB)

The size of the disk that this sensor monitors.

Name

The name of the disk that this sensor monitors.

Timeout (Sec.)

Enter a timeout in seconds for the request. Enter an integer. The maximum timeout value is 900 seconds (15 minutes).

If the reply takes longer than this value, the sensor cancels the request and shows a corresponding error message.

Result Handling

Define what PRTG does with the sensor result:

• Discard result: Do not store the sensor result.

• Store result: Store the last sensor result in the \Logs\sensors subfolder of the PRTG data directory on the probe system. The file name is Result of Sensor [ID].Data.txt. This setting is for debugging purposes. PRTG overwrites this file with each scanning interval.

In a cluster, PRTG stores the result in the PRTG data directory of the master node.

Primary Channel

Select a channel from the list to define it as the primary channel. In the device tree, the last value of the primary channel is always displayed below the sensor's name. The available options depend on what channels are available for this sensor.

You can set a different primary channel later by clicking below a channel gauge on the sensor's Overview tab.

Graph Type

Define how different channels are shown for this sensor:

• Show channels independently (default): Show a graph for each channel.
• Stack channels on top of each other: Stack channels on top of each other to create a multi-channel graph. This generates a graph that visualizes the different components of your total traffic.
  You cannot use this option in combination with manual Vertical Axis Scaling (available in the channel settings).

Stack Unit

This setting is only visible if you enable Stack channels on top of each other as Graph Type. Select a unit from the list. All channels with this unit are stacked on top of each other. By default, you cannot exclude single channels from stacking if they use the selected unit. However, there is an advanced procedure to do so.

Average Erase Count And Maximum Erase Count

The average erase count and the maximum erase count

Command Timeout

The command timeout count

Downtime

In the channel table on the Overview tab, this channel never shows any values. PRTG uses this channel in graphs and reports to show the amount of time in which the sensor was in the Down status

Erase Fail Count

The erase fail count

G-Sense Error Rate

The G-sense error rate count

Hardware ECC Recovered

The hardware ECC recovered count

Power Cycle Count

The power cycle count

Power Loss Protection Failure

The power loss protection failure count

Power-On Hours

The power-on hours count

Program Fail Count Total

The program fail count total

Read Error Rate

The read error rate count

This channel is the primary channel by default.

Read Error Retry Rate

The read error retry rate count

Reallocated Sectors Count

The reallocated sectors count

Reported Uncorrectable Errors

The reported uncorrectable errors count

SATA Downshift Error Count

The SATA downshift error count

Soft ECC Correction

The soft ECC correction count

Soft Read Error Rate

The soft read error rate count

SSD Erase Fail Count

The SSD erase fail count

SSD Life Left

The SSD life left count

SSD Program Fail Count

The SSD program fail count

Unexpected Power Loss Count

The unexpected power loss count

Unknown Channel

PRTG cannot match the ID of a found attribute with an internally defined channel name

Unused Reserved Block Count Total

The total unused reserved block count

Used Reserved Block Count Total

The total used reserved block count

Temperature Celsius

The temperature

Total LBAs Read

The total LBAs read

Total LBAs Written

The total LBAs written

Wear Range Delta

The wear range delta